[Strings]
ProgDev=PR1 or DECPROG connected
noProgDev=No Programming Device detected
Loco=Loco on track
noLoco=No loco on track
ProgTrk=Service Track connected
noProgTrk=No Service Mode Track
wait=be patient, please
Simple=simple
All=all
Mini=Address Only
Add=Add as
mmEntryName=Set the name of the new entry
Cancel=abort
Read=read
Write=write
Verify=verify
unknown=unknown
HardErr=hardware error
Error=error
save=save
noPort=no port
IniWrErr=cannot write to prolok.ini
WrDecErr=cannot write to decoder file
WrLogErr=cannot write to logfile
File=file
noPortAccess=com-port not available
OutOfMem=not enough memory
BitmapDesc=for bitmap description
InputValFormat=Only values from %d to %d allowed
Numeric=only numeric values allowed
Confirm=Confirm
Success=Successfull
FactoryReset=Do you really want to reset the decoder? All CV values, including the speed table at CV67-94 and the User ID at CV105 and 106, will reset to the factory default. The function is experimental, the result may be unpredictable. Reset anyway?
Wrong=wrong
Correct=correct
NACK=No Ack
Fail=Failure
Value=Value
Description=Description

[mainForm]
tsBasis=&Base CV
tsFunction=Fu&nction Mapping
tsSpeedTab=Speed &Table
tsMore=&More CV
tsSingleCV=s&ingle CV
tsRegister=Re&gister
pbRead=&Read
pbVerify=&Verify
pbWrite=&Write
mmFile=&File
mmLoad=&Load
mmSave=&Save
mmSaveAs=S&ave as
mmExit=&Exit
mmDecoder=De&coder
mmSetup=Set&up
mmHelp=&Help

Caption=LokProgrammer
lbCV8=CV8 Manufact.
lbCV7=CV7 Version
lbCV1=CV1 Short Address
lbCV2=CV2 Vmin
lbCV5=CV5 Vmax
lbCV6=CV6 Vmiddle
lbCV3=CV3 Acceleration
lbCV4=CV4 Deceleration
lbCV17_18=CV17+18 long Address
lbCV9=CV9 PWM-Frequency
lbCV19=CV19 Consist-Address
lbCV105=CV105 UserID1
lbCV106=CV106 UserID2
gbCV29=CV29 Configuration
lbCV29=CV29 decimal
CV29b0=Bit0 Direction revers
CV29b1=Bit1 28/128 Speed Steps
CV29b2=Bit2 Power Conversion 
CV29b3=Bit3 bidirectional Communication
CV29b4=Bit4 Use indiv. Speed Table
CV29b5=Bit5 Use long Address
CV29b6=Bit6 reserved
CV29b7=Bit7 Accessory Decoder
CV19b7=CV19 Consist Direction revers
pbDefaultFunctionMapping=Set Default Values
lbCV65=CV65 Kickstart
lbCV66=CV66 Forward trim
lbCV95=CV95 Backward trim
gbSpeed=Speed Table CV67=Step1..CV94=Step28
pbCalculate=Calculate Speed Table
pbDelSpeedTable=Delete Speed Table
lbDesc=Description
lbVal=Value
rbDecimal=decimal
rbBitmap=Bitmap
gbCVval=Value
lbDec=decimal
lbHex=hex
gbCVbin=binary
pbHardReset=Factory Reset
descR1=short Address (CV1), 1..127
lbReg=Register
lbRegVal=Value
lbRegDesc=Description
descR2=V Start (CV2), 0..255
descR3=Acceleration (CV3), 0..255
descR4=Decleration (CV4), 0..255
descR5=Configuration (CV29)
descR7=Version (CV7), R/O
descR8=Manufacturer-ID (CV8), R/O
mmNew=New
mmNewMini=minimal
mmNewExtended=simple
mmNewAll=all
mmChange=Change
mmAdd=Add
mmRemove=Remove
mmScan=Scan
mmHelpInhalt=Content
mmHelpIndex=Index
mmAbout=About ProLok


[setupForm]
Caption=Setup
lbPort=Port
lbWait=Wait Cycle
lblBulk=Retry Count
pbOK=Save
pbCancel=Undo
pbSetupHelp=Help
gbSetupDecoderMode=Programming Mode
cbDirectMode=direct
cbPageMode=CV
cbAutoMode=auto
cbUSBserial=USB-Serial-Adaptor
cbSafeMode=Verify after read and write
cbTest0Bit=Check Bit for 1 and 0 
cbIs6604=Extended Power-On Cycle
cbBulk=Stack Mode
gbSetupHardware=Device
lbl_Lang=Language
rbIsDDL=Booster + ACK detection circuit
rbIsPR1=Digitrax PR-1 oder DECPROG


[scanForm]
Caption=Decoder Scan
gbRange=CV-Ranges
lbFrom=from
lbTo=to
pbClose=Close
pbScan=Scan
pbCancel=Cancel


[formRemove]
Caption=Remove Profiles
pbRemove=Remove
pbCancel=Cancel

[aboutBox]
Caption=About ProLok

[faultListe]
Caption=Error List
lbHeadline=The requested Operation does not work correctly with the following CV:
pbClose=&close Window
